Login
Free Trial
Login

Supported Hardware

Cellocator CR-200

battery, vehicle
Cellocator CR200 (discontinued; replaced by CR300) is a compact size entry level GPS tracking device for fleet management and stolen vehicle recovery applications. Cellocator CR200 features a built-in GPS modem and internal quad-band antennas. The device can communicate via GPRS and SMS.
Cellocator CR-200 - Parameters Table
Parameter Type Unit Description Sources
acceleration.rms number Impact or free-fall acceleration RMS value where each of the axis is in 250µg units Module 28, Module 32
accelerometer.idling.duration number seconds Number of seconds idling detection is based on accelerometer Module 60
ain number volts Voltage on the analog input Message Type 0, Module 41
altitude.difference number meters Difference between the last stable altitude and current filtered one Module 28
battery.health number percentage Battery health level (SoH) Module 90
battery.state.bitmask number Battery state bitmask, 8 bits, indexed parameter Module 90
battery.temperature number celsius Battery temperature Module 90
baud.rate.enum number Used baud-rate enum value Module 28
calibration.matrix.index number Calibration matrix index, indexed parameter Module 43
calibration.phase number Calibration phase, 1 or 2 Module 70
calibration.state.enum number Calibration state, 0 - Started, 1 - OK, 2 - Bad Installation, 3 - In progress, 4 - Error Module 70
calibration.status boolean Calibration status, true - calibrating, false - calibration finished Module 30, Module 70
calibration.step number Calibration step, 0 - 10 Module 70
can.dtc array Diagnostic trouble code array read from CAN
May content list of OBDII codes or list of objects with codes.
Standard object parameter names used:
*standard* - Protocol standard (J1939, J1708(J1587), OBDII)
*mid* - Message Identifier (J1708)
*sid* - Subsystem Identifier (J1708)
*fmi* - Failure Mode Identifier (J1939, J1708)
*spn* - Suspect Parameter Number (J1939)
*sa* - Source Address (J1939, OBDII)
*oc* - Occurrence Count (J1939)
*cm* - Conversion Method (J1939)
*status* - Status of error code (active, pending, historical, permanent)		 Module 1, Module 38
can.dtc.number number Number of diagnostic trouble codes Module 1, Module 38
can.dtc.source number Number of bus ECU that reported the DTC Module 38
can.dtc.state.bitmask number CAN DTC transmission reason bitmask Module 38
can.pending.dtc string Pending diagnostic trouble code read from CAN Module 1
channel.id number ID of channel that received a message
crash.direction.enum number Crash direction - front, rear, left, right etc. Module 70
crash.duration number seconds Crash duration Module 35, Module 63
crash.event boolean Crash event detected Module 70
crash.id number Crash ID Module 35, Module 63
crash.max.acceleration number g Maximum acceleration (x or y) during crash Module 35, Module 63
crash.movement.status boolean Movement status associated with crash event: true - crash when driving, false - crash during parking Module 70
crash.orientation number Crash orientation Module 35, Module 63
crash.type number Crash type Module 35, Module 63
csa.event.reason number CSA event reason Module 30
csa.event.seqnum number CSA event numerator Module 30
csa.event.subreason number CSA event subreason Module 30
device.battery.level number percentage Device battery level Module 42
device.firmware.version string Firmware revision Message Type 11
device.id number ID of device that received a message
device.illuminance number lux Ambient light illuminance detected by device Module 42
device.io.bitmask number Device inputs and outputs status bitmask Message Type 0, Module 41
device.name string Name of device that received a message
device.pressure.altitude number meters Altitude above sea-level determined by air pressure detected by device Module 42
device.temperature number celsius Temperature of device Module 42
device.temperature.valid boolean Temperature readings validity Module 42
device.type.id number ID of device type of device that received a message
device.x.acceleration number g Acceleration sensor X-axis value detected by device Module 42
device.y.acceleration number g Acceleration sensor Y-axis value detected by device Module 42
device.z.acceleration number g Acceleration sensor Z-axis value detected by device Module 42
driver.id string Driver identification card id Module 30, Module 32, Module 70
driving.status boolean Driving status Module 30, Module 35, Module 63
engine.ignition.status boolean Engine ignition or ACC status Module 70
engine.on.idling.duration number seconds Number of seconds engine is on during idling session (engine running) Module 60
engine.status boolean Engine status Module 30
event.category number Event category Module 28
event.enum number Protocol-specific event code Module 28
external.alarm.status boolean External alarm status Message Type 0
external.memory number Size of external non-volatile memory Message Type 9
external.memory.type.enum number External non-volatile memory type Message Type 9
forwarded.message.code number Forwarded Message Code Message Type 8
fragment.control.byte number Fragment Control Byte Message Type 8
free.fall.event boolean Free fall evemt detected Module 28
fuel.level number percentage Fuel level percentage Message Type 9
fuel.volume number liters Fuel volume Message Type 9
gnss.idling.duration number seconds Number of seconds idling detection is based on valid GNSS position Module 60
gnss.status boolean GNSS receiver on/off status Message Type 0, Message Type 9, Module 41
gps.mode number GPS mode Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6
gsm.bsic number Base station identity code of the Mobile network (GSM, 3G, 4G, LTE, 5G, ...) Message Type 9
gsm.cellid number Mobile network (GSM, 3G, 4G, LTE, 5G, ...) base station ID Message Type 9, Module 46
gsm.lac number Mobile network (GSM, 3G, 4G, LTE, 5G, ...) location area code Message Type 9, Module 46
gsm.mcc number Mobile network (GSM, 3G, 4G, LTE, 5G, ...) country code Message Type 0, Module 4, Module 41, Module 46
gsm.mnc number Mobile network (GSM, 3G, 4G, LTE, 5G, ...) code Message Type 0, Module 4, Module 41, Module 46
gsm.network.roaming.status boolean Mobile network (GSM, 3G, 4G, LTE, 5G, ...) in roaming mode Message Type 0, Module 41
gsm.network.type string The type of the Mobile network the device is currently registered to Module 46
gsm.pcid number Physical layer Cell ID in the Mobile network (LTE and NR) Module 46
gsm.signal.dbm number dbm Strength of the Mobile network (GSM, 3G, 4G, LTE, 5G, ...) signal Message Type 9, Module 42, Module 90
gsm.sim.iccid string Integrated Circuit Card Id of SIM card of the Mobile network (GSM, 3G, 4G, LTE, 5G, ...) Message Type 9
gsm.timestamp number seconds Timestamp for the Mobile network (GSM, 3G, 4G, LTE, 5G, ...) data Module 46
hardware.interface.enum number Hardware interface and peripherals identifier Message Type 9
hardware.type string Hardware type Message Type 0
hardware.version.enum number Hardware version enum Message Type 0, Message Type 11, Message Type 9
harsh.acceleration.event boolean Harsh acceleration detected Module 70
harsh.braking.event boolean Harsh braking detected Module 70
harsh.turn.event boolean Harsh turn event detected Module 70
harsh.turn.left.event boolean Harsh left turn detected Module 70
harsh.turn.right.event boolean Harsh right turn detected, Module 70
ibutton.code string Hexadecimal code of connected iButton Message Type 0
ident string Device unique identifier like serial number, IMEI, etc
ignition.on.idling.duration number seconds Number of seconds egnition is on during idling session (ignition switch is on, motor is off) Module 60
impact.event boolean Impact event Module 28
internal.memory number Size of internal non-volatile memory Message Type 9
long.idling.duration number seconds Long idling duration from 'Long idling TO' to end of idling session Module 60
mandown.event boolean Mandown event detected Module 28
maneuver.abs.state number ABS sensor reading for braking event only Module 31
maneuver.average.speed number km/h Maneuver average speed Module 31, Module 58, Module 61
maneuver.average.speed.green number km/h Average speed in zone Green Module 58
maneuver.average.speed.red number km/h Average speed in zone Red Module 58
maneuver.average.speed.yellow number km/h Average speed in zone Yellow Module 58
maneuver.delta.speed number km/h Maneuver speed delta Module 31, Module 58
maneuver.duration number seconds Maneuver duration Module 31, Module 58, Module 60, Module 61, Module 63, Module 75
maneuver.engine.rpm.average number rpm Average engine RPM in maneuver Module 58
maneuver.engine.rpm.max number rpm Max engine RPM in maneuver Module 31, Module 58
maneuver.harsh.acceleration.event boolean Maneuver extended information: harsh acceleration event Module 75
maneuver.harsh.braking.event boolean Maneuver extended information: harsh braking event Module 75
maneuver.harsh.turn.angle number degrees Maneuver extended information: the angle of harsh turn event Module 75
maneuver.harsh.turn.left.event boolean Maneuver extended information: harsh turn left event Module 75
maneuver.harsh.turn.right.event boolean Maneuver extended information: harsh turn right event Module 75
maneuver.id number Maneuver id Module 30, Module 31, Module 58, Module 60, Module 61, Module 63
maneuver.max.fuel.flow number Maximum fuel flow during acceleration events Module 31
maneuver.max.speed number km/h Maneuver max speed Module 31, Module 58, Module 61, Module 75
maneuver.max.x.acceleration number g Maneuver extended information: maximum acceleration on the X azis Module 75
maneuver.max.y.acceleration number g Maneuver extended information: maximum acceleration on the Y azis Module 75
maneuver.overspeeding.event boolean Maneuver extended information: overspeeding event Module 75
maneuver.risk.score number Maneuver risk value 0-100 Module 31, Module 58
maneuver.start.latitude number degrees GPS location latitude of the maneuver start moment Module 31, Module 58, Module 60, Module 61, Module 63, Module 75
maneuver.start.longitude number degrees GPS location longitude of the maneuver start moment Module 31, Module 58, Module 60, Module 61, Module 63, Module 75
maneuver.start.position.valid boolean GPS is fixed at the maneuver start moment Module 75
maneuver.start.timestamp number seconds Timestamp of the maneuver start moment Module 75
maneuver.stop.latitude number degrees GPS location latitude of the maneuver stop moment Module 31, Module 58, Module 60, Module 61, Module 63, Module 75
maneuver.stop.longitude number degrees GPS location longitude of the maneuver stop moment Module 31, Module 58, Module 60, Module 61, Module 63, Module 75
maneuver.stop.position.valid boolean GPS is fixed at the maneuver stop moment Module 75
maneuver.stop.timestamp number seconds Timestamp of the maneuver stop moment Module 75
maneuver.time.green number seconds Time in maneuver zone Green Module 58
maneuver.time.red number seconds Time in maneuver zone Red Module 58
maneuver.timestamp number seconds Maneuver start time timestamp Module 31, Module 58, Module 60, Module 61, Module 63
maneuver.time.yellow number seconds Time in maneuver zone Yellow Module 58
maneuver.total.events.green number Total events in maneuver zone Green Module 58
maneuver.total.events.red number Total events in maneuver zone Red Module 58
maneuver.total.events.yellow number Total events in maneuver zone Yellow Module 58
maneuver.total.fuel.flow number Integral of Fuel flow Module 31
maneuver.total.severity.enum number Total Maneuver Severity: 1 - green, 2 - yellow, 3 - red Module 58
maneuver.type number Maneuver type Module 31, Module 58, Module 60, Module 61, Module 63
maneuver.x.acceleration.average number g Accelerometer X axes average Module 31
maneuver.x.acceleration.max number g Max accelerometer value X in maneuver Module 31, Module 58, Module 61
maneuver.y.acceleration.average number g Accelerometer Y axes average Module 31
maneuver.y.acceleration.max number g Max accelerometer value Y in maneuver Module 31, Module 58, Module 61
maneuver.z.acceleration.max number g Max accelerometer value Z in maneuver Module 31, Module 58, Module 61
measurement.source number Source of measurement Module 28, Module 40
message.buffered.status boolean Black box message
message.type string Message type
modem.type.enum number Modem type
module.id boolean Indexed parameter, that shows which modules are present in the message of type 11 Message Type 11
network.signal.rsrp number dbm LTE reference signal received power (RSRP) Module 46
onewire.sensor.serial string External 1-Wire sensor serial number in HEX representation Message Type 9
onewire.sensor.temperature number celsius External 1-Wire temperature sensor value Message Type 9
operation.mode string Unit's operation mode Message Type 0, Module 41
operation.mode.enum number Unit's operation mode numeric value Message Type 0, Module 41
operator.id string Type and ID of operator that triggered the event, refer to Cello-CANiQ Integration Manual Module 2, Module 25
overspeeding.event boolean Overspeeding detected Module 70
payload.hex string HEX Payload received from device Message Type 7, Message Type 8
peer string IP:port from which device connecting to the channel
pl.signature string PL signature - a unique 32-bit code identifying the PL, refer to Cello-CANiQ Integration Manual Module 2
position.altitude number meters Altitude value for position Message Type 0, Message Type 11, Module 30, Module 6
position.direction number degrees Heading angle at position detection moment Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6
position.hdop number Horizontal dilution of precision Message Type 11, Module 30, Module 6
position.latitude number degrees Latitude coordinate value Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6
position.longitude number degrees Longitude coordinate value Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6
position.satellites number Quantity of satellites used to calculate coordinates for given position information Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6
position.speed number km/h Instant speed at position detection moment Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6
position.timestamp number seconds Timestamp when coordinates were calculated Message Type 9
private.status boolean Device is in private mode
processor.enum number Processor family identifier Message Type 9
program.memory number Size of program memory Message Type 9
protocol.id number ID of protocol
protocol.version string Protocol version string Message Type 0, Module 41
record.seqnum number Registered record sequence number
report.reason number Transmission reason code Message Type 0, Module 41
report.reason.data number Additional transmission data Message Type 0, Module 41
report.reason.description string Report sending reason periodic, real time request, ignition on/off Message Type 0, Module 41
rollover.alarm.status boolean Roll over alarm state Module 70
rollover.event boolean Roll over event detected Module 35, Module 63
row.logging.status boolean Row logging status Module 30
samples.after.crash number Number of acceleration samples between crash and next GPS Module 35
samples.before.crash number Number of acceleration samples between last GPS before crash and crash Module 35
secondary.engine.status boolean Standby engine status Module 30
sensor.battery.dead.status boolean Sensor battery dead status, true - battery is dead, false - battery is recovered Module 28
sensor.battery.level number percentage External sensor battery level Module 28
sensor.battery.level.additional number percentage MultiSense battery level, received in additional information module Module 44
sensor.battery.low.status boolean Sensor battery status, true - battery low, false - battery ok Module 28
sensor.battery.voltage number volts Sensor battery voltage Module 28
sensor.connected.status boolean Sensor connected status, true - connected, false - not connected Module 28
sensor.door.status boolean Door opening status detected by sensor: true - opened, false - closed Module 28
sensor.error.code number Sensor problem code Module 28
sensor.group.id number Sensor group ID Module 28
sensor.humidity number percentage Humidity sensor value, i.e. relative air humidity level Module 28
sensor.humidity.additional number percentage Last measured humidity by the specific MultiSense, received in additional information module Module 44
sensor.humidity.alert boolean Sensor humidity alert Module 28
sensor.illuminance number lux Illuminance measured by light sensor Module 28
sensor.illuminance.additional number lux Last measured illuminance (light level) by the specific MultiSense, received in additional information module Module 44
sensor.last.timestamp number seconds Timestamp of the last communication with the sensor Module 28
sensor.last.timestamp.additional number seconds Timestamp of last communication from the specific MultiSense, received in additional information module Module 44
sensor.mac.address string External sensor MAC address Module 28
sensor.mac.address.additional string MultiSense MAC address, received in additional information module Module 44
sensor.magnet.status boolean Magnetic field detected by sensor Module 28
sensor.magnet.status.additional boolean Last measured magnetic state by the specific MultiSense, received in additional information module: false - magnet not present, true - magnet present Module 44
sensor.package.status boolean Package status read from external sensor: true - open, false - closed. Indexed parameter, measurement source is used as a parameter index Module 28
sensor.package.status.additional boolean Last detected package state by the specific MultiSense, received in additional information module: false - close, true - open Module 44
sensor.paired.status boolean Sensor paired status: true - paired, false - unpaired Module 28
sensor.power.on.status boolean Sonser power on status, true - sensor power-up, false - sensor power-down by button Module 28
sensor.reading.age number seconds Time elapsed from last sensor value reception Module 28
sensor.readings array MiltiSense measurement readings: array of JSON objects with 'value' and 'timestamp' files
sensor.readings.type number MiltiSense measurement readings type: 1 - temperature readings, 2 -humidity readings Module 40
sensor.report.reason number Sensor transmission reason code Module 28
sensor.rssi number dBm Sensor RSSI Module 28
sensor.rssi.additional number dBm MultiSense BLE signal RSSI, received in additional information module Module 44
sensor.temperature number celsius Temperature sensor value Module 28
sensor.temperature.additional number celsius Last measured temperature by the specific MultiSense, received in additional information module Module 44
sensor.temperature.alert boolean Sensor temperature alert Module 28
sensor.type.bitmask number Sensor HW type bitmask Module 28
sensor.x.acceleration number g Acceleration sensor X-axis value Module 28
sensor.x.acceleration.additional number g Last measured X acceleration by the specific MultiSense, received in additional information module Module 44
sensor.y.acceleration number g Acceleration sensor Y-axis value Module 28
sensor.y.acceleration.additional number g Last measured Y acceleration by the specific MultiSense, received in additional information module Module 44
sensor.z.acceleration number g Acceleration sensor Z-axis value Module 28
sensor.z.acceleration.additional number g Last measured Z acceleration by the specific MultiSense, received in additional information module Module 44
sensor.zone number Sensor zone number Module 28
serial.port.source number Serial Port Source Message Type 8
server.timestamp number seconds Timestamp when server received a message
short.idling.duration number seconds Short idling duration from 'Short idling TO'; to end of idling session or until 'Long Idling TO' Module 60
software.version string Software version string Message Type 0
software.version.enum number Software version enum Message Type 9
speed.source string Source of speed: gps or pulse frequency input Message Type 0, Module 41
time.after.crash number seconds Number of complete GPS seconds after crash Module 35
time.before.crash number seconds Number of complete GPS seconds before crash Module 35
timestamp number seconds Message timestamp Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6, Module 7
timestamp.key number Message timestamp in seconds with message sequence number appended as the value fractional part. Used to distinguish between several messages that have the same timestamp. Message Type 0, Message Type 11, Message Type 9, Module 30, Module 6, Module 7
time.valid.status boolean Time is accurate Message Type 0, Message Type 11, Message Type 9, Module 41, Module 6, Module 7
trailer.id string Trailer ID Message Type 0
trigger.cause.enum number Event trigger cause: 1 - from low to high, 2 - from high to low, 3 - both from low to high and from high to low, 4 - equal to threshold Module 25
trip.average.speed number km/h Average speed of the trip Module 32
trip.duration number seconds Trip duration Module 32
trip.eco.score number percentage A value representing the weighted Eco score of the trip Module 32
trip.engine.time number minutes Trip delta engine time Module 32
trip.fuel.consumed number liters Fuel consumed in the last trip Message Type 9
trip.highway.driving.score number Highway driving score of the trip Module 32
trip.highway.score.time number seconds Highway driving score time of the trip Module 32
trip.id number Trip ID increasing every engine-ON event Module 30, Module 31, Module 32, Module 58, Module 60, Module 61, Module 63
trip.idle.fuel.consumed number liters Trip idle fuel consumption Module 32
trip.idle.score number Idle score of the trip Module 32
trip.idle.score.time number seconds Idle score time of the trip Module 32
trip.long.idle.time number seconds Trip long idle time, based on GPS + accelerometer information,according to 2nd level threshold Module 32
trip.max.speed number km/h Maximum speed of the trip Module 32
trip.mileage number km Distance driven since engine start Module 32
trip.movement.fuel.consumed number liters Trip movement fuel consumption Module 32
trip.movement.time number seconds Time the vehicle has moved from Ignition on to Ignition off event or until driver was replaced Module 32
trip.safety.score number percentage A value representing the weighted safety score of the trip Module 32
trip.short.idle.time number seconds Trip short idle time, based on GPS + accelerometer information, according to 1st level threshold Module 32
trip.start.fuel.level number percentage Fuel level upon trip start Module 32
trip.start.timestamp number seconds Timestamp value upon trip start Module 32
trip.stop.fuel.level number percentage Fuel level upon trip end Module 32
trip.stop.mileage number km Trip end odometer value Module 32
trip.urban.driving.score number Urban driving score of the trip Module 32
trip.urban.score.time number seconds Urban driving score time of the trip Module 32
trip.x.acceleration.max number g Maximum accel input on X axis of the trip Module 32
trip.y.acceleration.max number g Maximum accel input on Y axis of the trip Module 32
trip.z.acceleration.max number g Maximum accel input on Z axis of the trip Module 32
variable.data.hex string Variable data in hex format, refer to Cello-CANiQ Integration Manual Module 2
variable.id string Variable ID, refer to Cello-CANiQ Integration Manual Module 2
vehicle.mileage number km Total calculated mileage Message Type 0, Message Type 9, Module 41
vehicle.odometer number Vehicle mileage in base units configured in device (km, miles, 100m, etc) Message Type 0, Message Type 9, Module 41
vehicle.type number Vehicle type. Protocol specific numeric value Module 35, Module 63
volatile.memory number Size of volatile memory Message Type 9
work.id number Work ID counter Module 28

At SHIFT, we revolutionize fleet management with AI. Our solutions ensure peak performance through predictive maintenance, real-time insights, and enhanced efficiency.

Platform
Solutions
Company
  • 1457 McCowan Rd, Toronto, ON M1S 5K7 Canada
Linkedin Youtube

Powered by Predictiv AI

Shift Technologies Canada Inc. Copyright © 2023 All Rights Reserved.